NACE-CIP2-001 Dumps - Kickstart your Career with Real Updated Questions
Earn Quick And Easy Success With NACE-CIP2-001 Dumps
NEW QUESTION # 28
When measuring the Dry Film Thickness Of liquid coatings applied to galvanized ferrous substrates the most commonly used instrument is the:
- A. Ultra Sonic DFT Gauge
- B. Eddy Current Gauge
- C. Tooke Gauge
- D. Magnetic Gauge
Answer: C
NEW QUESTION # 29
You can use magnifiers to examine all of the following EXCEPT
- A. Surface profile
- B. Surface cleanliness
- C. Blisters
- D. Mill scale
Answer: B
NEW QUESTION # 30
When using a destructive Paint Inspection Gauge the NACE inspector must:
- A. Ensure the glue on the dolly is properly applied prior to use
- B. Select the appropriate hand wheel based on the measured Dry Film Thickness prior to us
- C. Consult SSPC Guide 1 prior to use
- D. Determine the Dry Film Thickness of the coating prior to use
Answer: D
NEW QUESTION # 31
You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:
- A. Review the specification with the other inspector to see what method was specified
- B. Redo the pre-cleaning based on the other inspectors results
- C. Advise your QC Manager to change the ITP to the use of the salt smart meter
- D. Advise the other inspector he is using an incorrect method
Answer: A
NEW QUESTION # 32
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Cure stage
- B. Flow stage
- C. Gel stage
- D. Wetting stage
Answer: B
NEW QUESTION # 33
Inspection and Test plans are developed by referencing:
- A. The Specification, SDS, relevant Standards and Codes
- B. The Specification, Application Guidelines, 'Relevant Standards and Codes
- C. The Specification, TDS, relevant Standards and Codes
- D. The Specification, Safety Manual, Relevant Standards and Codes
Answer: C
NEW QUESTION # 34
Antifouling coatings are regulated by international treaties.
- A. True
- B. False
Answer: A
NEW QUESTION # 35
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. False
- B. True
Answer: A
NEW QUESTION # 36
When observing design defects the NACE Inspector should:
- A. Request that the item be rebuilt with a better design for coating
- B. Document the defect and the potential problems that could result
- C. Stop the job immediately
- D. Ignore the defect as the inspector can't change the design
Answer: B
NEW QUESTION # 37
Generally for safety considerations, waterjetting hose connections use
- A. a whip-lock device.
- B. a long wand.
- C. filters.
- D. an oil/water separator.
Answer: A
NEW QUESTION # 38
Thermal Spray coatings provide:
- A. Inhibitive protection
- B. Sacrificial protection
- C. Barrier protection
- D. Thermal protection
Answer: B
NEW QUESTION # 39
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.
- A. True
- B. False
Answer: A
NEW QUESTION # 40
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Document the readings at the end of the shift
- C. Check to See if the dehumidification equipment is operating correctly
- D. Advise the coating applicator supervisor of your readings
Answer: D
NEW QUESTION # 41
Pre-cleaning of work pieces will NOT remove
- A. oil or grease.
- B. dirt.
- C. mill scale.
- D. snow, ice or water.
Answer: C
NEW QUESTION # 42
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Enforce the additional requirement
- B. Call your supervisor
- C. Request clarification from the specifier
- D. Ignore the additional requirement
Answer: A
NEW QUESTION # 43
......
Free NACE-CIP2-001 pdf Files With Updated and Accurate Dumps Training: https://www.test4engine.com/NACE-CIP2-001_exam-latest-braindumps.html
Top-Class NACE-CIP2-001 Question Answers Study Guide: https://drive.google.com/open?id=1S5DxPa9xs9QwzlfnFEYD82kqzwUEW_L-