NACE NACE-CIP2-001 Exam Questions (Updated 2022) 100% Real Question Answers
Pass NACE NACE-CIP2-001 Exam Quickly With Test4Engine
NEW QUESTION 60
When using a destructive Paint Inspection Gauge the NACE inspector must:
- A. Consult SSPC Guide 1 prior to use
- B. Ensure the glue on the dolly is properly applied prior to use
- C. Select the appropriate hand wheel based on the measured Dry Film Thickness prior to us
- D. Determine the Dry Film Thickness of the coating prior to use
Answer: D
NEW QUESTION 61
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Safety Enforcement Costs
- B. Lower Supervision Costs
- C. Lower Application Costs
- D. Lower Coating Life Cycle Costs
Answer: D
NEW QUESTION 62
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. linings protect the contents and the container.
- B. linings are more durable than coatings.
- C. coatings are expected to degrade over time.
- D. coatings are more durable than linings.
Answer: A
NEW QUESTION 63
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)
- A. True
- B. False
Answer: A
NEW QUESTION 64
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. True
- B. False
Answer: B
NEW QUESTION 65
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Gathering
- B. Transmission
- C. Midstream
- D. Distribution
Answer: D
NEW QUESTION 66
When working with someone who is very concerned about Stability and maintaining adherence to the status-quo, the Inspector should try to:
- A. Implement immediate to get them motivated
- B. Challenge their value to the team and try to get them out of their comfort zone
- C. Give them as much advance notice as possible about upcoming changes
- D. Make sure they are the center of attention in all site meetings
Answer: C
NEW QUESTION 67
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. 3-Layer Polyethylene (PE)
- B. Coal Tar Enamel
- C. 2-Layer Polyethylene (PE)
- D. Fusion Bonded Epoxy
Answer: A
NEW QUESTION 68
It is always possible to see moisture on a steel substrate:
- A. True
- B. False
Answer: B
NEW QUESTION 69
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Consult your supervisor
- B. Request a re-blast of the item in question
- C. Verbally challenge the NCR
- D. Review the NCR with the other Inspector
Answer: A
NEW QUESTION 70
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. The floating structure is stationary
- B. It will result in a very slippery surface
- C. It doesn't contain biocide
- D. It contains biocide
Answer: D
NEW QUESTION 71
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that another NACE Inspector would understand
- B. Language that only in the project would understand
- C. Language that only technical experts would understand
- D. Language that the most would understand
Answer: D
NEW QUESTION 72
An Inspection and Test Plan is required when:
- A. It is always required
- B. When the Inspector requests one
- C. When the Coating Applicator requests one
- D. When the Owner specifies one
Answer: A
NEW QUESTION 73
Antifouling coatings are regulated by international treaties.
- A. True
- B. False
Answer: A
NEW QUESTION 74
Inspection and Test Plans are provided to:
- A. Outline the inspection steps, sequencing and pass/fail criteria
- B. So the contractor has a single document to reference
- C. So the Inspector doesn't have to read the entire specification
- D. To supersede the requirements of the product data sheets
Answer: A
NEW QUESTION 75
When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:
- A. Abrasive Blasting Equipment
- B. Scarifiers
- C. Power Tools
- D. Water Jetting Equipment
Answer: D
NEW QUESTION 76
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. a), b) and c)
- B. Lower the blast pressure
- C. Increase the standoff distance
- D. Move the nozzle quicker
Answer: A
NEW QUESTION 77
Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:
- A. Non-Conductive coatings applied to a conductive metallic substrate
- B. Magnetic coatings applied to a magnetic metallic substrate
- C. Conductive coatings applied to a magnetic metallic substrate
- D. Conductive coatings applied to a cementitious substrate
Answer: A
NEW QUESTION 78
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.
- A. True
- B. False
Answer: A
NEW QUESTION 79
Centrifugal blast cleaning requires:
- A. A large volume of air to propel the abrasive
- B. The use of single use abrasives
- C. Well maintained blast wheels
- D. Very large nozzles
Answer: C
NEW QUESTION 80
......
Real NACE NACE-CIP2-001 Exam Questions [Updated 2022]: https://www.test4engine.com/NACE-CIP2-001_exam-latest-braindumps.html
Prepare NACE-CIP2-001 Question Answers - NACE-CIP2-001 Exam Dumps: https://drive.google.com/open?id=1iH4Be_B3h72W50Xu22Eixk6d3Sw0wWtA