Verified 300-425 Dumps Q&As - 300-425 Test Engine with Correct Answers
Pass Your 300-425 Dumps as PDF Updated on 2021 With 99 Questions
Cisco ENWLSD 300-425 Practice Test Questions, Cisco ENWLSD 300-425 Exam Practice Test Questions
Passing the Cisco 300-425 exam together with one more test, namely Cisco 350-401, is the only requirement for the CCNP Enterprise certificate. Those IT specialists who pick this professional-level certification track are trained to troubleshoot, install, and maintain both local area networks (LAN) and wide area networks (WAN) for systems somewhere within the range of between 100 and 500 hubs.
Having this certificate validates your ability to investigate and execute both WAN and LAN networks. Also, you will be seen as a person who has what it takes to team up with the authorities on the issues identified with voice, wireless, video solutions, and advanced security. The individuals who hold Cisco CCNP Enterprise have a range of capabilities that are usually required in big and established businesses. Among the positions, which you will qualify to apply for after obtaining this certification, are the following:
- Network Director;
- Network Specialist.
- Network Security Experts;
- Network Technician;
- Network Analyst;
- Network Engineer;
- Network Investigator;
- Systems Engineer;
- Support Engineer;
With this professional-level certification under your belt, you will have more job opportunities and you can count on a high salary. From the PayScale figures, the average annual salary for a Network Administrator who is certified with CCNP Enterprise is $59,762. It usually starts at $49,485 and ranges up to $70,644 as seniority increases. The salary is usually highly dependent on the position. For example, a Network Engineer earns an average of $74,191.
NEW QUESTION 10
Drag and drop the characteristics from the left onto the correct functionalities on the right.
Answer:
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONS
NEW QUESTION 11
A wireless network consultant must assess an existing wireless LAN controller. Which section must the consultant check before replacing the old APs with APs that are IEEE 802.11ac-capable?
- A. controller PSU
- B. software version
- C. number of AP licenses
- D. throughput capacity
Answer: C
NEW QUESTION 12
A customer requires that two wireless APs be installed in a reception area, in a historic building, the impact of the APs on the appearance of the reception area must be minimized. Which two AP antennas should be used? (Choose two.)
- A. AP with a Yagi antenna
- B. AP with an integrated antenna
- C. AP with a dipole antenna
- D. AP with a monopole antenna
- E. AP with a patch antenna
Answer: A,E
NEW QUESTION 13
Which statement about creating a mobility group is true, excluding mobility anchors?
- A. The WLCs do not have to be of the same model or type to be a member of a mobility group, however each member should be running different software versions.
- B. Each WLC must use the same mobility name and be defined as a peer in each other's static mobility members list.
- C. If WLCs with HA SSO are deployed, each WLC in the WLC HA pair considered separately as a mobility peer.
- D. A mobility groups does not require all WLCs in the group to use the same virtual IP address.
Answer: C
NEW QUESTION 14
A customer has noticed that Client Band Select is enabled and no clients are utilizing the 5 GHz band. Which three parameters must be met to ensure that wireless clients use the 5 GHz band? (Choose three.)
- A. Ensure that channel bonding is enabled on the WLAN.
- B. Ensure that the client is dual-band capable.
- C. Ensure that the UNII-2 extended channels are enabled on the 802.11a radios.
- D. Ensure that the WLAN has 802.11a enabled.
- E. Ensure that the co-channel interference has not exceeded -85 dBm.
- F. Ensure that the client is receiving RSSI above the minimum band select RSSI threshold.
Answer: B,C,D
Explanation:
https://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/emob41dg/emob41dg-wrapper/ch3_WLAN.pdf
NEW QUESTION 15
An engineer Is trying to determine the most cost-effective way to deploy high availability for a campus enterprise wireless network that currently leverages three wireless LAN controllers. Which architecture should the engineer deploy?
- A. N+N solution without SSO
- B. N+1 solution without SS0
- C. N+N with SSO
- D. N+1 with SSO
Answer: D
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/wireless/technology/hi_avail/N1_High_Availability_Deployment_Gu
NEW QUESTION 16
An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services. What is the minimum requirement for the design?
- A. continuous -72 dBm coverage from one access point
- B. overlapping -72 dBm coverage from two access points
- C. continuous -67 dBm coverage from one access point
- D. overlapping -67 dBm coverage from two access points
Answer: C
NEW QUESTION 17
An engineer must configure the virtual IP address on multiple controllers in a mobility group. Which rule must the engineer follow to ensure proper roaming?
- A. Ensure that the DNS Host Name field is defined.
- B. Use a unique IP address for each WLC.
- C. Use the same IP address for each WLC.
- D. Ensure that the DNS entry is tied to the virtual IP address of the WLC.
Answer: D
NEW QUESTION 18
Which CLI command does an engineer use to validate that the redundancy peer of a Stateful Switchover pair of controllers is up and connected?
- A. eping
- B. ping
- C. mping
- D. rping
Answer: B
NEW QUESTION 19
Which three pieces of equipment are needed to conduct a fully measured wireless survey? (Choose three.)
- A. PoE battery
- B. tall tripod
- C. ladder
- D. spirit level
- E. goggles
- F. access point
Answer: A,B,F
Explanation:
https://www.cisco.com/c/en/us/td/docs/wireless/technology/mesh/81/design/guide/b_mesh_81/Site_Preparation_and_Planning.html
NEW QUESTION 20
Which CLI command does an engineer use to validate that the redundancy peer of a Stateful Switchover pair of controllers is up and connected?
- A. eping
- B. ping
- C. mping
- D. rping
Answer: B
Explanation:
NEW QUESTION 21
An engineer is designing a wireless network to support high availability. The network will need to support the total number of APs and client SSO. Live services should continue to work without interruption during the failover Which two requirements need to be incorporated into the design to meet these needs? (Choose two.)
- A. redundant WLC
- B. WLC 7.5 code or more recent
- C. 10 sec RTT
- D. controller high availability pair with one of the WLCs having a valid AP count license
- E. back-to-back direct connection between WLCs
Answer: D,E
Explanation:
Explanation
https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/7-5/High_Availability_DG.html#pgfId
NEW QUESTION 22
A wireless engineer is utilizing the voice readiness tool in Cisco Prime for a customer that wants to deploy Cisco IP phones. Which dBm range is the network inspected against?
- A. -85 to -67 dBm
- B. -78 to -65 dBm
- C. -85 to -65 dBm
- D. -72 to -67 dBm
Answer: A
Explanation:
https://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/34/user/guide/bk_CiscoPrimeInfrastructure_3_4_0_UserGuide/bk_CiscoPrimeInfrastructure_3_4_0_UserGuide_chapter_01010.html minimum is -90 and maximum is -67 for IP phone
NEW QUESTION 23
A network engineer is configuring high availability on an access point. What is the maximum number of controllers that can be configured?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
Explanation:
So max 2 will be supported on an AP.
NEW QUESTION 24
An engineer changed me TPC Power Threshold for a wireless deployment from the default value to -65 dBm The engineer conducts a new post deployment survey to validate the results What is the expected outcome?
- A. increased cell size
- B. increased received sensitivity
- C. decreased client signal strength
- D. decreased channel overlap
Answer: C
NEW QUESTION 25
A wireless engineer is designing a wireless network to support real-time applications over wireless. Which IEEE protocol must the engineer enables on the WLC so that the number of packets that are exchanged between an access point and client are reduced and fast roaming occurs?
- A. 802.11i
- B. 802.11k
- C. 802.11w
- D. 802.11r
Answer: D
Explanation:
NEW QUESTION 26
An engineer has successfully configured high availability and SSO using two Cisco 5508 Wireless LAN Controllers. The engineer can access the Active Primary WLC, but the Secondary Standby WLC is not accessible. Which two methods allow access to the standby unit? (Choose two.)
- A. SSH to the redundancy management interface of the primary WLC
- B. SSH to the management interface of the primary WLC
- C. SSH to the virtual interface of the secondary WLC
- D. via the console connection
- E. SSH to the service port interface
Answer: D,E
Explanation:
NEW QUESTION 27
A customer called with a requirement that internal clients must be on different subnets depending on the building they are in. All access points are operating in local mode and will not be modified, and this is a single controller solution. Which design approach creates the desired result?
- A. Create AP groups for each desired location, map the correct VLANs to the internal SSID, and add the access points for that location.
- B. Create an SSID place it to the desired VLAN under WLANs and configure 802.1x in ISE to assign the correct VLAN based on the SSID from which the client is authenticating
- C. Create mobility anchors for the SSID and on the controller under the internal SSID create a foreign map to the desired VLAN based on location.
- D. Create FlexConnect groups, place the access points in, and set the correct VLAN to SSID mapping based on location.
Answer: A
Explanation:
Explanation
https://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-vlan/71477-ap-group-vlans-wlc.html
NEW QUESTION 28
......
Wired & Wireless Infrastructure
This subject area makes up 30% of the overall content and measures the applicants’ skills in the following:
- Determining the requirements of logical infrastructure, which include the WLC/AP licensing needs based on the type of wireless architecture;
- Designing wireless networks that are high in density and their related components, including the campus, lecture halls, and conference rooms;
- Applying the design demands for data, location, video & voice, as well as hyper location wireless networks;
- Designing radio management (RxSOP, RRM, and RF profiles);
- Designing wireless bridging, such as Ethernet bridging, modes of operation, and WGB & roaming.
- Defining the requirements of physical infrastructure, such as mounting, cabling, switch port ability, AP power, and grounding;
Pass Cisco 300-425 Exam Info and Free Practice Test: https://www.test4engine.com/300-425_exam-latest-braindumps.html
Cisco 300-425 Real Exam Questions and Answers FREE: https://drive.google.com/open?id=1erZxuEskMX4e1rAadCMBLTTmunr7sJm5